How to Choose a Reliable Light Fastness and Colorfastness Tester Manufacturer?

Fading colors, chalking coatings, and cracked plastics after just a few months outdoors can turn a promising product into a customer complaint nightmare. Manufacturers across textiles, coatings, automotive parts, and plastics all face the same question: will this material hold its color and strength after years of sun, rain, and heat?

This article explains what separates a dependable Light Fastness and Colorfastness Tester manufacturer from an average one, and how LIB Industry's equipment helps engineers get accurate, repeatable answers before products ever leave the factory. A Russian university using LIB's Xenon test chamber shared their experience on July 21, 2026: "Good afternoon! We are satisfied with the purchase; there have been no complaints about the equipment. Thank you!"

Manufacturing Strength Backed by Real Numbers

LIB Industry has spent years building environmental and weathering test equipment for labs in over 60 countries, with production facilities covering more than 30000 square meters. Each xenon Light Fastness and Colorfastness Tester leaving the factory goes through more than 72 hours of continuous run-in testing before shipment, checking irradiance stability, black panel temperature accuracy, and water spray consistency. With a 4500W water-cooled xenon lamp and a spectral range of 280 to 800 nm, the equipment reproduces the full sunlight spectrum, including UV, visible, and infrared light, giving test results that closely match real outdoor exposure.

Standards LIB Industry's Equipment Fully Complies With

LIB Industry's Light Fastness and Colorfastness Tester is built to meet ASTM G155-21 for xenon arc exposure, along with ISO 4892-2 for plastics, ISO 105-B02 for textile colorfastness, and GB/T 8427 for automotive and coating applications. This wide standard coverage means one piece of equipment can support multiple industries and multiple quality certification requirements, saving customers from buying separate machines for separate standards.

ASTM G155 Testing Method with Specific Steps and Values

Following ASTM G155-21, the standard test cycle usually runs 102 minutes of light exposure followed by 18 minutes of light plus water spray, repeated continuously for the full test duration. Irradiance is commonly set at 0.35 W/m² at 340 nm or 0.55 W/m² at 420 nm, depending on the material type. Black panel temperature is held at 63°C ± 2°C for general materials, while chamber air temperature stays around 45°C to 50°C. Relative humidity during the dry cycle is typically kept at 50% RH ± 5%. Samples are mounted on a rotating rack holding up to 42 specimens at once, so every sample receives equal light exposure. Total test duration ranges from a few hundred hours for basic screening up to 2000 hours or more for long-term durability studies, with results measured using color difference (ΔE) readings taken at set intervals.

A coating and textile manufacturer in Vietnam recently purchased LIB Industry's xenon Light Fastness and Colorfastness Tester to test fabric dyes and painted panel samples for export markets. After running several batches, the customer reported strong satisfaction with the light uniformity across all 42 sample positions and the stability of irradiance readings over long test cycles.

The customer highlighted several advantages during feedback. First, the full-spectrum sunlight simulation impressed their team, since the equipment uses a 4500W water-cooled xenon lamp rated for up to 1600 hours of service life, paired with replaceable optical filters for daylight, window glass, and UV-extended conditions. This gives a controlled spectrum across 280 to 800 nm, fully compliant with ASTM G155 and related standards their export buyers required. Second, testing accuracy matched their expectations, with black panel temperature held steady within 35°C to 85°C (±2°C) and humidity adjustable from 30% to 98% RH (±2.5%), supporting alternating dry and wet cycles or spray cycles that closely mirror real outdoor weather. Color difference results stayed consistent across repeated tests, which matters greatly when certifying products for European and North American buyers. Third, the rotating sample rack holding all 42 positions kept every surface receiving the same light exposure and water spray throughout each cycle, so results stayed representative across the full batch rather than varying by position.

The customer also valued how the intelligent PID controller continuously logs irradiance and black panel temperature with automatic data export, while the multi-language interface and Ethernet/Wi-Fi connectivity let their quality team monitor tests remotely instead of checking the equipment in person every few hours. On the operating cost side, the closed-loop water circulation system with multi-stage filtration reuses the same water source repeatedly, keeping spray water clean while cutting water consumption and running costs significantly.

Beyond performance, the customer pointed to safety and long-term reliability. The equipment carries CE certification and meets IEC 61010 electrical safety requirements, giving their quality team confidence during daily operation. Free customization of sample holder sizes and test cycle programming let them switch between textile and coating protocols without buying new hardware. The 3-year warranty paired with lifetime technical support removed the worry of equipment downtime affecting production schedules, and LIB Industry's after-sales team arranged on-site training so local operators could run and maintain the equipment confidently. On the hardware side, the SUS304 stainless steel interior resisted corrosion even under constant humidity and spray cycles, keeping the equipment performing reliably after months of daily use.

Xenon and UV testers both simulate sunlight damage, but they work differently and suit different materials.

If your material will be exposed to full outdoor sunlight, including visible and infrared light, a xenon tester gives the most realistic simulation. If your priority is faster, lower-cost screening focused mainly on UV degradation, a UV tester like LIB Industry's UV-SI-260 model, with humidity reaching 95% RH and adjustable water spray cycles from 1 hour up to 9999 hours, offers a practical and budget-friendly option.

Popular Light Fastness and Colorfastness Tester and Aging Test Chambers

 

ISO 4892-2 xenon test chamber

Accurate Sunlight Simulation, Reliable Weathering Results, ASTM G155 Compliant Testing 

ASTM G155 UV Test Chamber

Fast UV Aging Evaluation, Accelerate Product Development 

UV Exposure Chamber for PV Modules

Designed for Solar Module Durability Testing, Stable UV Irradiance Control 

Temperature And Humidity Aging Chamber For Composites

Reproduce Real Climate Conditions, Enhance Product Reliability

IP69K Test Chamber

High-Pressure Water Protection Testing, Ensure Product Sealing Performance 

Benchtop Temperature And Humidity Aging Chamber

Compact Design, Professional Environmental Testing